Sep2026

September 26, 2026, Saturday

  • Shop Security
    • Installed sensor mounting brackets on each of the three shop garage bay doors
    • TODO: install the sensors, and wire to the sending unit
    • Tested the sending unit (EcoLink WS-232) from inside the shop, and the signal is strong enough
    • Tested a 5800PIR-RES unit from inside the shop, the signal is strong enough
  • Main Garage Door Opener Switch Panel
    • Removed the wood panel from the wall
    • Discovered that in addition to one CAT5 cable connecting the wall switch to the opener, there is a second CAT5 cable for each switch
      • Switch 1 (right-most) CAT5
        • This CAT5 cable goes to Lutron Panel #1 in the basement
        • Orange pair goes to switch 1 (Relay 3)
        • Blue pair goes to switch 2 (Relay 4)
    • Each of the other CAT5 cables behind switches 2, 3, and 4 are NOT connected
      • Their purpose and far end-point location are unknown
  • Lutron Lighting Control
    • Using toner I determined that the 'second' CAT5 cable in the Lutron Panel #1 enclosure is NOT one of the extra CAT5 cables behind the garage door opener wall switches
    • It goes to Honeywell Security Panel, presently unconnected
  • HIKVision Camera DVR
    • connected the HIKVision box to the network, it is currently configured for IP Address 192.168.1.230
    • Connected the gate PELCO camera feed to VIDEO #2 input
    • Connected a VGA monitor and using "admin/summer98" logged in
    • The gate camera is very unfocused, with distorted color balance, and the PELCO enclosure window is very dirty
      • TODO:
        • Clean PELCO enclosure window, inside and out
        • Adjust the mounting of the camera inside the enclosure
        • Adjust the focus at the camera
        • Adjust the color balance, first at the camera, then at the DVR
        • Then configure the HIKVision appropriately to record traffic at the gate
  • Patio Heaters
    • Label on the southern unit shows: Infra-Red Radiant, Inc., 1478 W. Tufts Avenue, Englewood CO 80110, 303-761-1444 and 800-748-2678
    • Internet search shows that they still exist (infraredradiant.com) and the units that I have are likely rebranded Detroit Radiant Products "Re-Verber-Ray" product
    • They require 24VAC from an external CLASS-2 transformer to be supplied over typical thermostat wire, the presence of the voltage turns them on, and no-voltage turns them off
    • Saved some literature to the Appliances section of Buckskin files
    • Q: Did/does the Lutron system control these heaters? Is there a hidden controlled 120VAC socket somewhere, maybe under the BBQ, or the attic?

September 18, 2026, Friday

Water Softener - Intermountain Softwater - "Twin-Sensor Glacier" unit installation

  • Called and spoke to "Spencer" a couple of weeks ago and discussed the possibility of installing a Twin-Sensor water softener here in Pocatello. I was told that they don't serve Idaho, but would make an exception in our case, because of our past history of using their equipment in our Orem home. "Rogan", the owner of the company, reviewed the water test results from Culligan and agreed that the new Twin-Sensor equipment would handle our well water just fine.
  • "Eric" arrived last Friday (September 11) for the installation, but didn't have the correct tools for dealing with my 1-1/4" piping, and we rescheduled for the next week.
  • "Eric" arrived at 10AM to install the new unit
    • He disconnected the old Culligan HE Twin system and we set that aside
    • He and I discussed the orientation of the new softener. We moved the reverse osmosis holding tank (blue Wellmate 80) over to the right, then positioned the new water conditioner in front of the that:
      • Water flows into the pre-filter (charcoal-filler mineral filter), then into the Twin Sensor, then from there out to the household, with the reverse osmosis unit taping water from the output of the water conditioner, which then feeds from it's holding tank the culinary taps and ice makers
    • He used PEX-B piping to do the plumbing and it looks neat and tidy.
    • We tested water at the basement bathroom faucet, the kitchen island sink and the Hers Master Bathroom sink.
      • The basement water was showing perfectly soft, no grains (immediate blue color using the 5B test kit, without any drops)
      • The kitchen sink water shows hard (22 grains), turns out that the two kitchen sink cold taps are plumbed to use pre-softener water
      • The master bathroom water showed perfectly soft, no grains (immediate blue color)
    • Eric loaded the old Culligan equipment and removed it
  • So we now have better water conditioning, which feels better. At last!

September 12, 2026, Saturday

Front Porch

  • Removed 2 LED standard bulbs from the inner porch, one of which had gone dim
  • Installed 2 LED flood light bulbs, (Good Value (Walmart) 100W-equivalent dimmable)